NZD
USD
EURO
GBP
HKD
AUD
CAD
SGD
CHF
Product Description
Four colors for choosing, black, blue, red, purple.
E-MI V2-RPG-302 Drift Tuned Gyro 3 CH For Competition Drifting
Gyroscope Parameters
Dimension:25*24*10mm
Weight:13g
Operating voltage:3.6-6.0V
Operating current:20mA/6V
Support the servo pulse width:1520uS(50Hz&333Hz)
Operating temperature range:-10℃+45℃
Control systerm:PID control systerm
Sensor:vibrating gyroscopic sensor
Angular velocity:maximum±5000/s
Description:
Drift Steering Gyro is a steering gyroscope with optimum characteristics for RWD (Rear Wheel Drive) drift. The gyro is compatible with 2 and 3 channel transmitter/receivers. With a 2 channel system, adjustments are achieved on the gyro. With a 3 channel transmitter, adjustment function can be achieved through the propo function, without touching the gyro body.
While realizing the steering reaction which is essential for RWD drift, it prevents hunting due to hypersensitive reaction and enables real drift driving.
Hold that perfect drift angle combined with high speeds with this Gyro pre-loaded with a customized firmware for Drifting! Comes with aluminum Heat-sink case for high efficiency cooling. Features adjustments to suit every servo on the market, ranging from analog to digital servos and you can also reverse the direction which the gyro acts. The gain (Or sensitivity) can be adjusted on the fly for drifters with transmitters featuring more than three channels and also can be adjusted on the gyro itself.
Feature:
Drift Steering Gyro w/End Point Adjustment.Although it is a high response, it is possible to adjust the maximum turning angle according to the situation without changing the real steering operation.
For: Competition Grade Drifting
Material: Aluminum Case
Include:
Aluminum Case High Stability Gyro (1 pc)
Adjustment Screwdriver (1 pc)
Manual (1 pc)
Compatibility
Yokomo YD-2,Yokomo YD-4,Yokomo YD-4MR and other rc car.
LED Status Display:
| Fast blink | Initialization | |
| Slow blink | Self sensitivity adjustment | Stop |
| Constant blink | Transmitter sensitivity adjustment | Work |
Product Description
V2 RPG-302 new high-voltage version gyroscope adapts aluminum case and has digital
and analog mode. Advantage of being compatible with high voltage: ESC can open 7.4V
BEC power supply, high voltage servo can work in 7.4V environment, and the strength
and speed are much higher than the 6V environment.
Friendly Tip: The built-in sensitivity adjustment knob of the gyroscope is made of plastic
and the range of rotation is Limit, so please use the special slotted screwdriver to adjust.
When it is tightened, don't forcefully continue to screw, otherwise it will be damaged!
Function of gyroscope:
The gyroscope belongs to auxiliary device of steering gear, which can be used to correct
the deviation or excessive tail of RC car. It is commonly used for drift or F1 car models.
The Gyro can apply to any models theoretically, but the actual effect depends on the
setting of the Gyro (such as setting of sensitivity / correction direction).
Instruction:
Switch 1: Servo Type setting, flip switch up for analog servos, down for digital servos.
Switch 2: Sensitivity direction setting, flip switch up for opposite direction, down for
positive direction.
LED
1. Quick flash when power on means the gyro is initializing and will calibrate a middle
point of the gyro and the remote controller's direction channel. Don't move the
gyroscope and change the direction channel of remote controller.
2. When the LED stops blinking and is constantly lit, it means that the signal of
sensitivity setting channel has been received. The sensitivity can be set by remote
controller and the servo output range can be set by the potentiometer on the
gyroscope, increasing the output value towards clockwise direction
3.If LED blinks slowly, it means that the signal of sensitivity setting channel has not
been received. The sensitivity can be set by the potentiometer on the gyroscope,
clockwise increasing Maximum value of sensitivity and servo range.
